If you want to find out more about
Leak Tester CETATEST 515
Talk to us at :
(65) 6749 9697
sales@lfc.com.sg
The CETATEST 515 is devised as a fully automatic working leak tester for the detection of leaking parts within the cycle time of the production process. Ceta Leak Tester CETATEST 515 works precisely by sensing inputs from its one channel air compressor with at least of 6 - 10 bar and 0.5 bar above test pressure resp. 50 mbar under evacuation pressure (ISO 8573-1) towards the workpiece in such a way that your product can be tested on production line (with or without testing jig). Then, the value of tested workpiece is stored within its internal memory. The cost-effective CETATEST 515 leak detector also provide data output via USB port which then can be conveniently saved into a flash drive for traceable data record or further analysis of acceptable parameter via CETA PC software and spreadsheet as well. Compared to Ceta Leak Tester CETATEST XS, the CETATEST 515 leak detector are equipped with much smaller range of 500 Pa and detailed mode of testing. This innovative instrument have three different mode of configuration. “Closed components - high resolution” can be used for test parts, which can not be filled, so called “closed components”. The type “pressure loss - high speed” can be used for leak tests of very small test parts in high speed production cycles. The configuration “pressure rise” has a very high measurement signal and integrated components (e.g. stop valve, primary pressure control). Your investment on CETA Leak Tester CETATEST XS will lead your way to unlocks higher level of precision in detecting very small ratios of test part volumes on mass production system. Your operator can simply follow your parameter of programmable test with pass-faill decision by seeing the measured value on its LCD Screen responsibly. Due to its reliable accuracy within an automatic approach, this instrument's versatility is highly regarded by many end user in the inspection of turbochargers, tests of micro switches, sensors, relays, valves, watches, medical equipment, mechatronics, pneumatic workpiece and many more. Ceta Leak Tester CETATEST 515 Features: Leak testers with differential pressure sensor. Measurement range of > ± 500 Pa / ± 5,000 Pa (displayed resolution: 1 Pa). Unit of measurements are Pa, hPa, psi, Pa/s, hPa/s, mbar*l/s, psi/s, ml/min, ml/h, l/min, l/h. Can also be combined with mechanical pressure regulator and other set of pressure gauge as well. Input of compressed air supply with 6 mm plug-in fitting and optionally up to three pneumatically driven outputs. Delivered with with CE certificate and DAkkS calibration certificate withhout additional cost. Detailed result statistics, cycle counter, indicator for service intervals, countdown indicator, registration of parameter change, recording of measurement series and measurement curves, Dynamic Link Library (DLL) for RS-232 interface programming. Optimised for leak testing of very small test parts in high speed production cycles. To serve your interest on Ceta Leak Tester CETATEST 515, kindly contact our sales department.
The CETATEST 515 is devised as a fully automatic working leak tester for the detection of leaking parts within the cycle time of the production process. Ceta Leak Tester CETATEST 515 works precisely by sensing inputs from its one channel air compressor with at least of 6 - 10 bar and 0.5 bar above test pressure resp. 50 mbar under evacuation pressure (ISO 8573-1) towards the workpiece in such a way that your product can be tested on production line (with or without testing jig). Then, the value of tested workpiece is stored within its internal memory. The cost-effective CETATEST 515 leak detector also provide data output via USB port which then can be conveniently saved into a flash drive for traceable data record or further analysis of acceptable parameter via CETA PC software and spreadsheet as well.
Compared to Ceta Leak Tester CETATEST XS, the CETATEST 515 leak detector are equipped with much smaller range of 500 Pa and detailed mode of testing. This innovative instrument have three different mode of configuration. “Closed components - high resolution” can be used for test parts, which can not be filled, so called “closed components”. The type “pressure loss - high speed” can be used for leak tests of very small test parts in high speed production cycles. The configuration “pressure rise” has a very high measurement signal and integrated components (e.g. stop valve, primary pressure control).
Your investment on CETA Leak Tester CETATEST XS will lead your way to unlocks higher level of precision in detecting very small ratios of test part volumes on mass production system. Your operator can simply follow your parameter of programmable test with pass-faill decision by seeing the measured value on its LCD Screen responsibly. Due to its reliable accuracy within an automatic approach, this instrument's versatility is highly regarded by many end user in the inspection of turbochargers, tests of micro switches, sensors, relays, valves, watches, medical equipment, mechatronics, pneumatic workpiece and many more.
Ceta Leak Tester CETATEST 515 Features:
- Leak testers with differential pressure sensor.
- Measurement range of > ± 500 Pa / ± 5,000 Pa (displayed resolution: 1 Pa).
- Unit of measurements are Pa, hPa, psi, Pa/s, hPa/s, mbar*l/s, psi/s, ml/min, ml/h, l/min, l/h.
- Can also be combined with mechanical pressure regulator and other set of pressure gauge as well.
- Input of compressed air supply with 6 mm plug-in fitting and optionally up to three pneumatically driven outputs.
- Delivered with with CE certificate and DAkkS calibration certificate withhout additional cost.
- Detailed result statistics, cycle counter, indicator for service intervals, countdown indicator, registration of parameter change, recording of measurement series and measurement curves, Dynamic Link Library (DLL) for RS-232 interface programming.
- Optimised for leak testing of very small test parts in high speed production cycles.
To serve your interest on Ceta Leak Tester CETATEST 515,
kindly contact our sales department.
TECHNICAL SPECIFICATION
Ceta Leak Tester CETATEST 515 Ordering Guide:
| Operating methods | One channel operation |
| Signal processing | Fast 24-Bit-A/D-Converter (internal resolution: effective 0.01 Pa)Real-time processing of the measurement signals |
| Pneumatic | Minimized volume to optimize the resolution |
| Processing | Real time microcontroller system, 16-Bit µC / 40 MHz |
| Sensors | Differential pressure sensor, relative pressure sensor |
| Measurement ranges | ± 500 Pa / ± 5,000 Pa (displayed resolution: 1 Pa); other ranges on request |
| Result units | Pa, hPa, psi, Pa/s, hPa/s, mbar*l/s, ml/min, ml/h, l/min, l/h |
| Electronically regulated test pressure ranges | -1,000 mbar, 200 mbar, 1,000 mbar, negative gauge pressure and positive gauge pressure ranges can be combined other pressures and mechanical pressure regulator on request |
| Test modes | Pressure loss, “closed component – high resolution” pressure loss, “high speed”, pressure rise |
| Test options | Prefill (incl. multiple filling), program series, smooth filling, analysis of the filling and stabilizing curve, consecutive zero results, temperature compensation, variable zero point, test repetition/automatic test time adjustment, free programmable control valves for each program |
| System control | Still-Alive-Check with differential pressure sensor control, patented automatic function control (option), control of the compressed air supply |
| Programmable test phases | Delay, pre-filling, filling, stabilizing, measuring,venting, reservoir filling, flooding, re-filling |
| Test mode specific limits | Prefill pressure, filling pressure, test part specific reject and rework levels |
| Handling | Intuitive menu including password protected user levels |
| Parameter Memory | 64 individual parameter driven test programs with alpha-numeric program namesParameters of the test programs can be exported resp.imported via the test device interfaces or by usage of a USB storage device. |
| Power Supply and Power Consumption | 100 – 240 V AC, 47 – 63 Hz, 0.6 – 0.3 A depending on stage of expansion max. 60 W |
| Compressed air supply | 6 - 10 bar and 0.5 bar above test pressure resp. 50 mbar under evacuation pressure (ISO 8573-1) |
| Pneumatic Connection | Input (compressed air supply): 6 mm plug-in fitting Port for test part: 3 x 1.7 mm fitting, 3 mm clamping ring [option] Up to three pneumatically driven outputs [option] |
| Dimension and Weight | Width: 345 mm, Height: 145 mm (3U), Depth: 435 mm Approximately 10 kg |
| Standard Delivery | Special packing, power cord, operating manual and documentation on CD, declaration of conformity (CE), calibration certificate, D-Sub-plug including cable for inputs and outputs (PLC-communication) |
| Certificates | CETATEST 515 (500 Pa) conform with DAkkS calibration certificate [DAkkS = Deutsche Akkreditierungsstelle] |
| Optional Accessories | Filter combination, standard leak, leak tight 3/2-way-valve, RS-232 / Ethernet-adapter, control- and evaluation software, more in the CETA accessories catalogue |
|
Notes: The CETATEST 515 is a full automatically working leak tester for the detection of untight parts within the cycle time of the production process. The leak tester is available in three different types. The configuration “closed components - high resolution” can be used for test parts, which cannot be filled, so called “closed components”. It is possible to detect very small ratios of test part volumes [0,03 ml < ∆V < 1,0 ml).The type “pressure loss - high speed” can be used for leak tests of very small test parts in high speed production cycles. The configuration “pressure rise” has a higher measurement signal (compared to the CETATEST 810) and integrated components (e.g. stop valve, primary pressure control), which are normally part of the external measurement circuit. |
For further detail on Ceta Leak Tester CETATEST 515,
kindly contact our sales department.
Request a Quote
Request A Quote
Please complete the below form to receive further information.
